The Vapefly Jester Pod System is one of the first to offer two ways to enjoy your vape. A rebuildable deck and replaceable stick coil.
Vapefly Jester review

Chinese manufacturer Vapefly burst on to the vape scene in 2017. They have a large, impressive catalogue which includes the Pixie RDAGalaxies MTL RDTAGalaxies MTL RTABrunhilde RTA and not forgetting our last review for them Galaxies MTL starter kit.

What Can We Expect from the Jester Pod System By Vapefly?

In the last couple of years I have reviewed many pod systems, sadly many of them didn’t hit my ‘OMG this is an amazing vape’ for many reasons, chiefly they were either to tight a draw or the coils burnt out far too quickly for my liking.

Not to mention the fact that a lot of them are money magnets due to non replaceable coils.

The only pods that I can truly say I personally like are the Aspire Breeze 2 and the Smok Nord.

That is until I read our Michelle’s Preview of the Vapefly Jester where my interest was piped!Vapefly Jester in hand

The Jester, along with the Smoant Pasito, offers both a refillable cartridge with a replaceable 0.5Ω mesh coil and a pod that has a re-buildable deck. This enables you to either build your own coils or take advantage of some of the excellent pre built coils out there.

Vapefly even include a couple of 1.0Ω coils to get you started!

Each cartridge features an easy convenient top fill and hosts a 2ml liquid capacity, the battery is a decent 1000mAh with 3 levels of power and you even get to choose between 7 different wacky and plain designs.pod kit parts

Is an RBA the next obvious evolution for pod kits? You decide!

This kit was kindly sent to us for review by Vapefly, as always my thoughts and views on this product are my own after a considerable testing period.

In The Box

  • 1 x Vapefly Jester Battery
  • 1 x Vapefly Jester Cartridge
  • 1 x 0.5Ω Mesh coil pre installed
  • 1 x Vapefly Jester Dripping Cartridge
  • 2 x 1.0Ω 28g Coils
  • 2 x Firebolt cotton
  • 1 x USB Cable
  • 1 x Bag of spares
  • 1 x User Manual

In The Box Contents

Features

  • Size: 91x33x18.2mm
  • Battery: 1000mAh
  • Pod Capacity: 2ml
  • 3 Output Modes: 3.3/3.8/4.8V
  • Recommended Resistance: 0.8-1.5Ω
  • Colours available: Black, Gorilla, Skull, Jester, Joker, Zomble, Silver

Design and Build Quality

The Vapefly Jester comes packaged nicely in a card box with a paper over sleeve,PackagingThe device measures 91mm vertically, 33mm horizontal and 18.2mm in depth.Vapefly Jester full side view

Jester Cartridges (Pods)

Both pods are made of plastic and silicone. In the case of Pod 2 the RBA deck is made of stainless steel.Vapefly Jester pods

Pod 1

Included is a replaceable 0.5Ω mesh stock coil with an adjustable airflow base, to remove the coil and base simply pull it from the bottom of the pod, the coil simply screws into the airflow base.Jester pod 1 coil and airflowThe pod has a small button on one side.cap release on pod 1 When pushed this will flip open the cover to reveal the silicone fill port plug, this plug is rather a tight fit.Fill port on pod 1 Over all I’d say this pod is pretty much standard.

Pod 2

In my opinion this is the main selling point of this kit!Vapefly Jester p2 To remove the cap simply rock and pull the cap off to reveal the stainless steel RBA deck, the build deck is designed to take a single micro coil.Vapefly Jester rebuildable deck postsThe airflow is handled by a centre single airflow tube. The 2 small slots either side of the airflow go down in to the tank to hold your cotton for wicking.

If you look carefully you will see a small hole above one of the wick slots. This is an airflow that feeds the centre tube and also acts as an anti suction lock.Fill port on RBA podThe fill port is again plugged by a silicone plug that seems to seat better than the stock coil version.

The pod cap has a stainless steel cover embedded into the plastic, this sits over the coil. It has a doming effect to catch stray liquid and condensation which will then drip back down to the coil/cotton.rba cap on pod 2

Jester Pod Battery

As you can see Vapefly have sent me the Skull design Jester, which is quite cool looking.Vapefly Jester mod The skull design over wrap has a soft handle.Vapefly Jester designThe Pod connection points are gold plated.Gold battery contacts

The device runs an impressive 1000mAh internal battery and while the body is plastic it seems hard wearing.

Operation Button and USB port

The Vapefly Jester pod has one operation button for both firing the device and changing the 3 step voltage settings.fire buttonThe micro USB charge port is located on the bottom of the device which is a pain because you have to lay the Jester down to charge it.USB Port

Sides of the Battery | Body

The Jester has what Vapefly call a child lock, handled by a button on either side of the device. By pressing both these together the pod will be released from the battery.Child Lock release

The whole kit in my opinion has been manufactured to the highest standard, the design is good and the quality is fair, I got to admit the Jester does feel wonderful in the hand.Vapefly Jester p2 hand

How Does the Vapefly Jester Pod System Perform?

While Pod 1 performs admirably as a sub ohm standard mouth to lung cartridge – for this review I am going to use the RBA Cartridge (Pod 2) as this is to me is the selling point of the kit.

I will be using one of the two pre made coils and firebolt cotton sent with the kit, I will also be using Coconut Cappuccino e-juice from Coffee House with 6ml of Salt Nic.Vapefly Jester seal check

Basic Quick Start Guide

Choose which pod is right for you, if using Pod 1, prep the coil, fill the pod and leave for a couple of minutes for the cotton to soak up more liquid – enjoy

Pod 2 RBA Cartridge

Before building on your RBA deck ensure that the mod is switched off!

  1. Unscrew the post screws and seat your coil, screw the post screw so they pinch the wire, clip the tails as near to the deck as you can get. I have spaced the coil slightly so pre burning isn’t necessary.Vapefly Jester pod 2 in coil
  2. Position the coil the coil, straighten and tidy it, you know the drill lol.
  3. Place your cotton through the coil, and tucking it down the wick slots “not too far”.
  4. Soak your cotton and fill the 2ml tank with e-liquid. dripping e juicehow to fill the Vapefly Jester rba

No need to wait for the cotton to soak up more liquid just vape away and enjoy.

Battery operation

To turn the Jester on/off hit the fire button 5 times

To change your voltage setting hit the fire button 3 times, you have 3 output modes

  • 3.3v Purple
  • 3.8v Blue
  • 4.8v Green

Vapefly recommend that if you use the 0.5Ω mesh coil in Pod 1 only to use 3.3v or 3.8v settings.

Mini Tool Kit

I have been using the mini tool kit today that was sent to me by Vapefly along with the Jester!Vapefly tool kit closed To be fair it contains everything you’d need to build a coil all housed in a very sturdy portable plastic case in a velveteen draw bag!Vapefly tool kit mini open The kit has been living in my work bag the last week just encase of a coil related emergency!

Flavour and Vapour Quality

1.0Ω Pre-Made Coil

Set on 4.8v for a warm vape, I have experienced good flavour, almost RDA flavour, the resulting vapour production is acceptable, the airflow is defiantly a mouth to lung draw.

I would have liked to have seen a slightly bigger airflow with a control as the draw is almost too tight for me to enjoy the vape.Vapefly Jester pod system in hand

Pod 2 Notes

I have had a great time with the RBA Pod. It is real simple to coil and wick although I would recommend that users have some knowledge of ohms law if building their own coils, as you can’t check the resulting resistance of the coil unless you have an electrical multimeter, which I don’t, just experience in coiling!

Vapefly recommend a resistance of 0.8 to 1.05Ω for Pod 2.firing the coil

I found 3 ways to utilise the Jester deck for wicking!

  1. Coil and wick like an RDTA – cotton down through the slots.
  2. Coil and wick by just tucking the cotton a tiny amount to plug the slots this results in you tipping your jester to wick the cotton.
  3. Coil and wick like an RDA placing the cotton over the slots and dripping liquid onto the cotton, leaving the 2ml tank empty, caution using this method may result in the cap becoming loose overtime.

While the deck is on the small side I had no problem seeing it to coiling it.

I would suggest the smaller gauge of wire say up to 28g for your micro coil any larger and the wire slots will be too small to hook your wire.

Battery life

The 1000mAh battery, from fully charged, lasted me about 4 hours. I’m a heavy vaper so those that aren’t quite so heavy should get a longer life from a full charge.Vapefly Jester size next to ejuice bottle

Pod 1 Notes

As a quick mention about Pod 1, it works great with the adjustable airflow, although the coil is 0.5Ω and the draw is on the looser side it is most surely is a mouth to lung vape. I did manage to get a very restricted direct to lung draw.

I love the idea the coils can be swapped out, “money saver” in the long run.Mesh Pod Coil on Jester I have been using it on the Purple, 3.3v setting, with the airflow cut by half.

The flavour and vapour production are very acceptable pretty much what you would expect from a standard pod!Vapefly Jester front view I have not figured out the coil life yet as I have been mainly using Pod 2 (RBA). I have a couple of little niggles with Pod 1.

  1. You cannot fill the cartridge while it attached to the Jester because the way it is situated the flip cap does not open fully.Pod 1 cap open
  2. The cartridge cap is a little fickle and flips open if the device is handled incorrectly.

Pros

  • RBA Deck
  • Standard cartridge with replaceable stock coil
  • Fair flavour
  • Good for mouth to lung vaping
  • Adequate vapour production
  • Comfortable to hold
  • 3 settings
  • Good quality of manufacture

Cons

  • No RBA adjustable airflow
  • Pod 1 flip cap
  • Bottom USB charge port

Final Review Verdict

Finally a fairly decent pod system with a rebuildable deck.

While I’ve had some niggles I have enjoyed my time with this kit and playing with the RBA pod. I can see myself using the Jester as part of my regular line up!

Would I recommend the Vapely Jester RBA pod system?

Yes I would, to new vapers with the standard pod and to the more experienced flavour chasers who have knowledge of building their own coils.

Would I buy the Vapelfy Jest Pod Mod kit again due loss or damage?

If Vapefly were to add a better airflow with control to the RBA I would consider it.

Have you used this rebuildable pod system? Let us know your thoughts in the comments below!

Kevin Worthing Vaper
Kevin Jeffrey

Hi my name is Kevin, I started vaping back in 2009 mainly because my little boy at 3 years old was starting to copy the way daddy smoked a cigarette! Over the years I have gained a good amount of experience with different types of vaping hardware but I'm just a normal guy who enjoys sharing my experiences. This is why I started my Youtube vape review channel in 2014. To date the channel has had over 500,000 views. Being disabled, vaping has given me a gateway to meeting people from all different walks of life, many of those I would not have met under other circumstances. The way I look at my reviews is, if I can convince just one person to give up the stinky’s my job is done. I class myself as a tinkerer as I like to take things apart to see how they work and put them back together, yes that includes e-cigarette mods! One day I would like to be able to design my own mod. I am a dedicated father, and husband to my sweetheart of nearly 30 years! Family to me comes before anything else.

REVIEW OVERVIEW
Build and Design Quality
7
Ease of use
8
Ease Building RBA Deck
9
Flavour
8
Vapour Production
8
Price Point
8
Hi my name is Kevin, I started vaping back in 2009 mainly because my little boy at 3 years old was starting to copy the way daddy smoked a cigarette! Over the years I have gained a good amount of experience with different types of vaping hardware but I'm just a normal guy who enjoys sharing my experiences. This is why I started my Youtube vape review channel in 2014. To date the channel has had over 500,000 views. Being disabled, vaping has given me a gateway to meeting people from all different walks of life, many of those I would not have met under other circumstances. The way I look at my reviews is, if I can convince just one person to give up the stinky’s my job is done. I class myself as a tinkerer as I like to take things apart to see how they work and put them back together, yes that includes e-cigarette mods! One day I would like to be able to design my own mod. I am a dedicated father, and husband to my sweetheart of nearly 30 years! Family to me comes before anything else.
vapefly-jester-pod-system-reviewA great option for vapers that like the idea of having an RBA deck on a pod mod!

3 COMMENTS

  1. Hi. I’m just new to vaping and a friend recommended this jester pod. And so I bought. However, after using pod 1 for about a week now, it taste a little burnt. Is it time to change the coil? In the future, how do I know if I need to replace the coil for pod 1? Thank you for you kind sir for your response

    • Hi, a week for the coil is about right for changing, in my experience with this and other stock coils drop the voltage down when you detect a burnt taste you should get another couple of days from the coil, I’m lazy and anything I can do to lengthen the life of a stock coil I’ll do to say money lol

  2. I’m Pod user and much type of pod being used before but for this i have much pro than con from many aspect of this jester pod provided.I really recommend this coz it very easy to rewick than others rba pod

LEAVE A REPLY

Please enter your comment!
Please enter your name here